Offering exclusive benefits and discounts, discover more about our Membership and Patron schemes. You can also support the theatre by making a one-off donation.
| Task | Button Sequence (from Manual) | |------|-------------------------------| | Change cutoff | [MENU] → Parameter → Cutoff → Choose λc | | Switch to Rz (instead of Ra) | [MENU] → Parameter → Evaluation → Rz | | Output to printer | After measurement → [PRINT] | | Set measurement length | [MENU] → Condition → Length (default 4mm) | | Calibrate | [MENU] → Calibration → Place standard → Enter value |
Features a built-in rechargeable battery that supports roughly 500 measurements on a single charge. mitutoyo sj-201 user manual pdf
The Mitutoyo SJ-201 user manual PDF typically includes the following sections: | Task | Button Sequence (from Manual) |
list of compatible accessories for specific measurement tasks? AI can make mistakes, so double-check responses Copy Creating a public link... You can now share this thread with others Good response Bad response 14 sites SURFACE MEASUREMENT SURFTEST SJ-201 / SJ-301 Page 4. Keys for changing the operating setup. The upper cover of the display unit can be pushed back to operate the keys under ne... Allmetech SURFACE MEASUREMENT SURFTEST SJ-201 / SJ-301 Measurement data. Measuring set up, calculation result, profile, BAC diagram (selectable) Print method. Thermal printer. Data tran... Allmetech SURFACE MEASUREMENT SURFTEST SJ-201 / SJ-301 When the START/STOP key is pressed in measuring mode, the probe begins to travel. When measurement is finished, the display change... Allmetech Surftest SJ-201P * 12BAA303. Connecting cable (1m) * 178-602. Roughness specimen (inch/mm)* * 353134. Calibration stand. * 538612. Phillips screwdr... BergEng.com SURFTEST SJ-201/301 - Gagesite Surftest SJ-201 Series. The display unit has IP53 protection level against dripping water and dust. The built-in battery if fully ... Gagesite Surftest SJ-201P Calibration Mode: Pressing the [CAL/STD/RANGE] key in the measurement mode, the calibration mode is entered allowing the detector ... BergEng.com Surftest SJ-201P 64AAA779. Printing Method. Line Thermal Dot Printing. Interface. Serial (RS-232C) Input Buffer. 2KB. Printing Width. 1.89" Dot Den... BergEng.com Surftest SJ-201P Calibration Mode: Pressing the [CAL/STD/RANGE] key in the measurement mode, the calibration mode is entered allowing the detector ... BergEng.com SURFTEST SJ-201/301 - Gagesite For SJ-201P/SJ-301. • Popular standard drive unit. Standard drive unit. Measuring force: 4mN. Stylus profile: Tip radius: 5µm. Mea... Gagesite SURFTEST SJ-201/301 - Gagesite Function Customization Desired parameters can be selected for calculation and display. Statistical processing Maximum value, minim... Gagesite Mitutoyo SJ-201P Portable Surface Roughness Tester Rentals Large characters are displayed on the large easy-to-view LCD. Portable for easy measurement anywhere necessary. The detector/drive... Advanced Test Equipment Corp. - ATEC Surface Roughness Tester User's Manual. No.99MBB079A5. SERIES No.178. Read this User's Manual thoroughly before operating the instrument. After reading, re... Boston University HOW TO USE MITUTOYO SURFACE ROUGHNESS TESTER ... May 16, 2023 — You can now share this thread with others
Skipping calibration is the #1 cause of bad readings. The manual details:
The SJ-201 runs on a 4-line LCD with soft keys — not a touchscreen. Its logic is non-intuitive by modern standards. Without the manual, you will likely:
Offering exclusive benefits and discounts, discover more about our Membership and Patron schemes. You can also support the theatre by making a one-off donation.